Nogniet Online - Blog

A step-by-step guide to creating a mosaic tabletop. Material checklist A table Assorted tiles Old towel Tile underlay, cut to size (optional) Construction adhesive (optional - eg liquid nails) Tile adhesive Grout in desired colour Clean rags Edge trim or beading PVA glue Step 1: break the tiles Before starting, you need to decide on a theme for your tabletop design. Designs like waves, swirls, or perhaps an animal or floral image are not overly ambitious for a first timer effort. Select your tiles to suit the colours you will need to create your design. Now put on your safety glasses and break your tiles by placing them face down in the towel, covering the tile back with the towel, and striking with the hammer. You’re trying to create 20mm-40mm fragments, so don’t pulverise the tile. Any larger pieces can be trimmed down using the tile nippers later. Step 2: prepare the tabletop If your table top is timber, sand it back to create an even surface for the tile adhesive to stick to. If your table top is plastic, metal or laminate, you will need to cover the original table top with the tile underlay. Adhere the underlay to your table top using some construction adhesive and allow it to dry before attempting to work with the new surface. Step 3: lay out the tiles Now draw out your design on the table top, taking the time to get the lines and shapes right. Once you are satisfied with the design, start filling in the patterns by dry-fitting the tile fragments in place (Fig. 1). Don’t leave more than 5mm or so between tile fragments, and don’t sit tiles too closely side by side as the grout will not be able to penetrate correctly later on. Use the tile nippers, always wearing your safety glasses, to trim tiles to size. We found holding the nippers and tile fragment inside a cardboard box was a good way of containing any flying fragments and dust when doing this. Take the time at this stage to ensure that your tile fragments are the right shape and size to do justice to your design. Step 4: stick down the tiles Once you have completely covered the tabletop with tile fragments in the design of your choice, get comfortable and start gluing (Fig. 2). Start from one corner, and working with one tile fragment at a time, use your old knife or filling blade to apply tile adhesive to the back of each tile frag-ment. If your tiles are large enough, tile adhesive can be applied directly from its container. Press it down firmly onto the table top - but be careful not to squeeze all of the adhesive out from under it. Continue in this way until all tiles have been stuck down, using the tweezers to work with small or fiddly tiles. When all the tiles are all stuck down, use your wooden ruler to check the level of the new surface you have created. Press down any raised tiles, and use your tweezers to pull up and reglue any tiles that seem too press down - you are aiming for a uniform levelled surface that will take grout well. Follow the manufacturer’s instructions in regard to drying time. Step 5: apply the grout Make up the grout in accordance with the directions on the pack. Once it is ready to go, apply it in sections to the tabletop, working the grout into the gaps between the tiles with the grout squeegee (Fig. 3). It is preferable to overfill rather than underfill at this stage. Keep working back and forth until you have removed as much of the excess grout as possible with the squeegee, and ensured that all gaps are filled with grout. Allow the table to sit for ten minutes, then fill the large bucket with clean water. Take the barely damp, flat, smooth sponge and start wiping over the surface of the tiles to remove the excess grout. Rinse out the sponge constantly - you should be able to get one or two good swipes before needing to rinse. Make sure you wring out the sponge well each time. Once you are satisfied with the finish on your tabletop, leave the grout to dry. Check the manufacturers instructions on the grout packet for recommended drying times. Step 6: finishing Once the grout is dry, a haze will probably form across the tiles no matter how careful you were with cleaning off the excess grout. Use your clean rag to polish the haze off. Now you need to finish the edges of your table. Use some beading, mitre cutting the corners to create neat edges (Fig. 4). To do this, simply select some beading or edge trim from your Mitre I0 store wide enough to cover the old edge of the table and the new tiled surface, and measure the length of each side of the table. Cut the mitres so that the lengths you have just measured form the short side of the mitre. Apply the construction adhesive to each length, and press into place along the side of the table, using the PVA glue to fix the mitre joins together. Use tape or some other form of temporary fixing to brace the four pieces in place while the glue cures. Once dry, sand back and finish the trim as desired.

Do your own mosaics

25 February 201725 February 2017 nogniet

A step-by-step guide to creating a mosaic tabletop. Material checklist A table Assorted tiles Old towel Tile underlay, cut to size

Read more